Showing posts with label lime. Show all posts
Showing posts with label lime. Show all posts

Monday, October 8, 2018

Roasting the Frit

Diderot & d'Alembert, L'Encyclopédie (1772)
Raking Out Roasted Frit
Making glass from raw materials involves several steps. In his 1612 book on glassmaking, L'Arte Vetraria, Antonio Neri breaks the process down into parts so that, "given a bit of experience and practice, as long as you do not purposely foul-up, it will be impossible to fail." Pure white sand, or preferably quartz river stones which Neri calls "tarso" is broken up and pulverized into a fine powder. The initial work can be done by heating the stones in a furnace, then dropping them into a vat of clean cold water, where they will fracture due to the thermal shock. The process was often repeated multiple times. From there, the pieces are pulverized in a stone mortar and pestle. Stone, because metal tools would contaminate the quartz, and in the end tint the glass. Finally, a powder is obtained by grinding with a stone tool on a flat granite "porphyry stone." This powdered quartz is the main ingredient of glass.

The second critical ingredient is the flux, what Neri calls "glass salt" or "soda." This can be obtained from mineral sources, but European glassmakers in the seventeenth century extracted all their salt from certain plants. The powdered quartz was mixed with the salt and a third ingredient, which is critical, lime. Lime is simply calcium oxide used by builders to make cement. It is nothing more than pulverized seashells roasted to a high temperature. Neri advises using two pounds of lime for every hundred pounds of salt. He specifies that it should be added to all his frit recipes, but it is not clear that he understood its critical importance; without lime, the glass would be subject to attack by mere water, eventually decomposing. This mixture of soda, lime and silica when heated in a kiln would chemically react forming "frit." The combined materials were raked around in a kiln for a long period (many hours) and finally formed nut sized pieces. It was cooled and heaped into piles in dry cellars where it was aged for a time. This is where some chemical "magic" in glassmaking takes place. The glass salt or soda dramatically lowers the melting temperature of the quartz, all the way down to a point that was easily achieved in a wood fired furnace. When a batch of glass was made, the aged frit was then melted in furnace crucibles and skimmed to remove excess salt, which floated on the surface; it could foul the glass, and smelled terrible. The melted glass, now ready to work, was sometimes colored and finally made into objects by gaffers. 

Neri obtained his glass salt from products shipped by traders from the Levant (eastern Mediterranean). It was supplied as the dried, partially charred remains of special plants that grow in arid seaside conditions; 'Kali' and 'Soda'. Shipping them this way cut down on weight and volume, and prevented rotting. These plants contain large amounts of sodium carbonates. This is a white powder, chemically identical to what we know as "washing soda." He advises, 
In buying either of these make sure it is richly salted. This may be determined by touching it with the tongue in order to taste its saltiness; but the surest way of all is to do a test in a crucible and to see if it contains much sand or stones, a thing common in this art and very well known by glass conciatori.
He crushes any large pieces of the product in a stone mortar, and sifts the result through a fine screen, ensuring that most of what remains is salt.  
As the common proverb of the art of glassmaking says: a fine sieve and dry wood bring honor to the furnace. Then with any of these sodas, 100 pounds of soda ordinarily requires 85 to 90 pounds of tarso.
Neri sets up large cauldrons of clean water over brickwork stoves, adds the plant product and boils the water. He strains the insoluble parts out and reduces the liquid by evaporation until crystals of the salt start to form on the surface. He skims these off and continues the process. Finally he carefully dries the product. Our glassmaker describes several variations of this process, including one in which he takes extreme measures to ensure the purity of the salt and clarity of the finished glass. In all, this is a task that could easily take several weeks to perform for the amount of frit to fill a single pot for the gaffer to work.

Not content with the established materials, our glassmaker experimented extensively with other plants: 
[U]se the husks and stalks of fava beans after the farmhands have thrashed and shelled them. With the rules and diligence prescribed for the Levantine polverino salt, extract the salt from this ash, which will be marvelous, and from which a frit can be made using well-sifted white tarso, as is described throughout this work. A very noble frit will result, which in the crucible will make a crystal of all beauty. The same may be made from the ashes of cabbages, or a thorn bush that bears small fruit, called the blackberry, even from millet, rush, marsh reeds, and from many other plants that will relinquish their salt. *
*These other plants produce potassium carbonate salts with similar properties to sodium carbonate.
** This post first appeared here 9 December 2013.

Friday, July 13, 2018

Lime

Vintage 1920's Water Glass Label.
The temperature of 1500 degrees (825C) was comfortably within reach of seventeenth century glassmakers like Antonio Neri. It was also achievable in much earlier times and was used in one of the earliest chemical reactions of  human industry; the production of "lime" by heating seashells or limestone to the above mentioned temperature. This is the point at which these materials give up the carbon dioxide gas bound into their chemical structure, leaving behind calcium oxide, otherwise known as lime.

What makes lime so useful is a property early Roman engineers knew well; that when mixed with water, lime undergoes a chemical reaction that releases heat and quickly solidifies into a rock-hard mass that is impervious to the elements. The Romans used it as a construction material; they mixed it with ash, clay, sand and stones to form mortar, cement and concrete. It has played a critical role ever since in the construction of buildings, roads and monuments.

Today it is perhaps not an obvious choice in imagining the supplies of a seventeenth century alchemist’s cabinet; lime does not require exotic methods to produce, it was made in industrial quantities and readily available as a construction material. Nevertheless, lime played an important part in many diverse chemical preparations of the day. Antonio Neri mentions it numerous times in his writing. He used it in his lute recipe; a hard, cement like coating which protected alchemical glassware in direct flame and sealed joints. He also used it to extract the color from flowers in the production of paints. Most notably, he used lime as an ingredient in the formulation of glass itself. 

Lime turns out to be a rather critical ingredient in glassmaking and the central player in a mystery about the history of glass that to this day has not been satisfactorily explained. Neri obtained the white powder from suppliers as "lime cake." Early in his book, L'Arte Vetraria, he states it should be used in all his glass recipes. 
Take lime salt, which is used for building. Purify this salt and mix it with ordinary Levantine polverino salt in the proportion of 2 pounds per 100, which is 2 pounds of lime salt, to every 100 pounds of polverino salt, purified and well made, as previously described. With this salt mixture, you can make yourself ordinary frit, and put it in the crucible to clarify. I will refer to this frit from now on in the recipes for cristallino, cristallo, and common glass. This way you will have cristallo quite subtle and beautiful.[1]
The above excerpt is the full extent of Neri's discussion on lime in glassmaking. An interesting point here is that he does not say why lime is so necessary, but it is. [2] He must have known that adding too much lime will cause glass to become cloudy, the exact opposite effect that he was after. What is not so clear is if Neri (or anyone else in that period) knew that too little lime allows glass to dissolve slowly when exposed to water. 

One of the great enduring mysteries in the history of glassmaking is the question of exactly when it was clearly understood that lime was so important. The subject became a matter of deliberate chemical investigation in the eighteenth century, but the use of lime extends much earlier. Some of the earliest glass fragments known contain healthy amounts of lime. Neri's ambiguous endorsement is the first mention in print, but even among much earlier manuscripts, its role is unclear. In the first century, Roman author Pliny made a cryptic reference to adding seashells to the glass melt, but again, without further explanation. [3] Analysis of ancient glass often shows a significant lime content; seemingly more than could be reasonably accounted for by happy accident or contamination. The ingredient is never mentioned in most surviving early recipes. Of course, it may be that  lime is present in many ancient glass artifacts precisely because those artifacts are the ones that have survived without dissolving.

Some have speculated that calcium could have been introduced inadvertently as seashell fragments when sand was crushed into powder for glassmaking. This hypothesis is certainly possible, but it seems suspect considering just how much seashell would be required and how fussy the glassmakers were in obtaining pure white sand from particular locations. However, a distinction must be made between knowing that sand from a particular location makes good glass, and knowing what is in that sand. 

Perhaps the most famous such site for good glassmaking sand is the "Belus" [Na'aman] River outlet in what is now northern Israel. This is where the story of the discovery of glass takes place, as told by Pliny and other early writers. Sailors were driven here by a storm, they used natron (glassmaking salt) [4] from their cargo to hold their cooking pots up over a beach fire, and when the natron mixed with the sand in the fire, glass was formed. Or so the story tells. The nearby Phoenician cities of Tyre and Sidon are known to have hosted a thriving glass industry. The sand in this area is composed of exceptionally pure quartz, with a healthy amount of calcium from shells ground down from wave action. Together these make an ideal mix for stable glass. 

There is some evidence that experimenters such as Basil Valentine were aware that glass without lime would dissolve as early as 1520. [5] For what it is worth, I can contribute some anecdotal evidence from the twentieth century. There is a well-known product called water-glass that is essentially composed of dissolved glass without the lime. [6] My glass artist friend Emilio tells me that growing up on Murano in Venice, his mother regularly preserved fresh eggs by dipping them in water-glass, which when dry, formed a hard seal over the existing shell. Presumably, she learned the technique from her own mother. I do not know of any early references, but the use of water-glass clearly indicates a knowledge of the role lime played.

There are other explanations possible for the addition of lime to glass. Lime was a commodity that was made since ancient times, in furnaces very similar to the ones producing glass. In fact, Neri specifies the use of a “limekiln” for the production of his enamels. The archaeological remains of Tyre and Sidon show prolific use of lime based plaster and mortar in their construction practices and there are indications of lime making facilities. It seems only good business sense that the same furnaces making glass may have also been making lime. Cross contamination, and even experimentation would be a natural outcome. 

[1] Neri 1612, ch 7.
[2] As an aside, magnesia (MgO) can also serve as a stabilizer in glass.
[3] Pliny, Natural History v.36, ch. 66.192.
[4] Natron is a mix of sodium carbonates. 
[5] Basil Valentine, et al. see footnote 6 of the Wikipedia article on sodium silicate for a discussion.
[6] Sodium Silicate.
* This post first appeared here in a slightly different form on 10 October 2014.

Wednesday, November 22, 2017

Roasting the Frit

Diderot & d'Alembert, L'Encyclopédie (1772)
Raking Out Roasted Frit
Making glass from raw materials involves several steps. In his 1612 book on glassmaking, L'Arte Vetraria, Antonio Neri breaks the process down into parts so that, "given a bit of experience and practice, as long as you do not purposely foul-up, it will be impossible to fail." Pure white sand, or preferably quartz river stones which Neri calls "tarso" is broken up and pulverized into a fine powder. The initial work can be done by heating the stones in a furnace, then dropping them into a vat of clean cold water, where they will fracture due to the thermal shock. The process was often repeated multiple times. From there, the pieces are pulverized in a stone mortar and pestle. Stone, because metal tools would contaminate the quartz, and in the end tint the glass. Finally, a powder is obtained by grinding with a stone tool on a flat granite "porphyry stone." This powdered quartz is the main ingredient of glass.

The second critical ingredient is the flux, what Neri calls "glass salt" or "soda." This can be obtained from mineral sources, but European glassmakers in the seventeenth century extracted all their salt from certain plants. The powdered quartz was mixed with the salt and a third ingredient, which is critical, lime. Lime is simply calcium oxide used by builders to make cement. It is nothing more than pulverized seashells roasted to a high temperature. Neri advises using two pounds of lime for every hundred pounds of salt. He specifies that it should be added to all his frit recipes, but it is not clear that he understood its critical importance; without lime, the glass would be subject to attack by mere water, eventually decomposing. This mixture of soda, lime and silica when heated in a kiln would chemically react forming "frit." The combined materials were raked around in a kiln for a long period (many hours) and finally formed nut sized pieces. It was cooled and heaped into piles in dry cellars where it was aged for a time. This is where some chemical "magic" in glassmaking takes place. The glass salt or soda dramatically lowers the melting temperature of the quartz, all the way down to a point that was easily achieved in a wood fired furnace. When a batch of glass was made, the aged frit was then melted in furnace crucibles and skimmed to remove excess salt, which floated on the surface; it could foul the glass, and smelled terrible. The melted glass, now ready to work, was sometimes colored and finally made into objects by gaffers. 

Neri obtained his glass salt from products shipped by traders from the Levant (eastern Mediterranean). It was supplied as the dried, partially charred remains of special plants that grow in arid seaside conditions; 'Kali' and 'Soda'. Shipping them this way cut down on weight and volume, and prevented rotting. These plants contain large amounts of sodium carbonates. This is a white powder, chemically identical to what we know as "washing soda." He advises, 
In buying either of these make sure it is richly salted. This may be determined by touching it with the tongue in order to taste its saltiness; but the surest way of all is to do a test in a crucible and to see if it contains much sand or stones, a thing common in this art and very well known by glass conciatori.
He crushes any large pieces of the product in a stone mortar, and sifts the result through a fine screen, ensuring that most of what remains is salt.  
As the common proverb of the art of glassmaking says: a fine sieve and dry wood bring honor to the furnace. Then with any of these sodas, 100 pounds of soda ordinarily requires 85 to 90 pounds of tarso.
Neri sets up large cauldrons of clean water over brickwork stoves, adds the plant product and boils the water. He strains the insoluble parts out and reduces the liquid by evaporation until crystals of the salt start to form on the surface. He skims these off and continues the process. Finally he carefully dries the product. Our glassmaker describes several variations of this process, including one in which he takes extreme measures to ensure the purity of the salt and clarity of the finished glass. In all, this is a task that could easily take several weeks to perform for the amount of frit to fill a single pot for the gaffer to work.

Not content with the established materials, our glassmaker experimented extensively with other plants: 
[U]se the husks and stalks of fava beans after the farmhands have thrashed and shelled them. With the rules and diligence prescribed for the Levantine polverino salt, extract the salt from this ash, which will be marvelous, and from which a frit can be made using well-sifted white tarso, as is described throughout this work. A very noble frit will result, which in the crucible will make a crystal of all beauty. The same may be made from the ashes of cabbages, or a thorn bush that bears small fruit, called the blackberry, even from millet, rush, marsh reeds, and from many other plants that will relinquish their salt. *
*These other plants produce potassium carbonate salts with similar properties to sodium carbonate.
** This post first appeared here 9 December 2013.

Monday, August 21, 2017

Lime

Vintage 1920's Water Glass Label.
The temperature of 1500 degrees (825C) was comfortably within reach of seventeenth century glassmakers like Antonio Neri. It was also achievable in much earlier times and was used in one of the earliest chemical reactions of  human industry; the production of "lime" by heating seashells or limestone to the above mentioned temperature. This is the point at which these materials give up the carbon dioxide gas bound into their chemical structure, leaving behind calcium oxide, otherwise known as lime.

What makes lime so useful is a property early Roman engineers knew well; that when mixed with water, lime undergoes a chemical reaction that releases heat and quickly solidifies into a rock-hard mass that is impervious to the elements. The Romans used it as a construction material; they mixed it with ash, clay, sand and stones to form mortar, cement and concrete. It has played a critical role ever since in the construction of buildings, roads and monuments.

Today it is perhaps not an obvious choice in imagining the supplies of a seventeenth century alchemist’s cabinet; lime does not require exotic methods to produce, it was made in industrial quantities and readily available as a construction material. Nevertheless, lime played an important part in many diverse chemical preparations of the day. Antonio Neri mentions it numerous times in his writing. He used it in his lute recipe; a hard, cement like coating which protected alchemical glassware in direct flame and sealed joints. He also used it to extract the color from flowers in the production of paints. Most notably, he used lime as an ingredient in the formulation of glass itself. 

Lime turns out to be a rather critical ingredient in glassmaking and the central player in a mystery about the history of glass that to this day has not been satisfactorily explained. Neri obtained the white powder from suppliers as "lime cake." Early in his book, L'Arte Vetraria, he states it should be used in all his glass recipes. 
Take lime salt, which is used for building. Purify this salt and mix it with ordinary Levantine polverino salt in the proportion of 2 pounds per 100, which is 2 pounds of lime salt, to every 100 pounds of polverino salt, purified and well made, as previously described. With this salt mixture, you can make yourself ordinary frit, and put it in the crucible to clarify. I will refer to this frit from now on in the recipes for cristallino, cristallo, and common glass. This way you will have cristallo quite subtle and beautiful.[1]
The above excerpt is the full extent of Neri's discussion on lime in glassmaking. An interesting point here is that he does not say why lime is so necessary, but it is. [2] He must have known that adding too much lime will cause glass to become cloudy, the exact opposite effect that he was after. What is not so clear is if Neri (or anyone else in that period) knew that too little lime allows glass to dissolve slowly when exposed to water. 

One of the great enduring mysteries in the history of glassmaking is the question of exactly when it was clearly understood that lime was so important. The subject became a matter of deliberate chemical investigation in the eighteenth century, but the use of lime extends much earlier. Some of the earliest glass fragments known contain healthy amounts of lime. Neri's ambiguous endorsement is the first mention in print, but even among much earlier manuscripts, its role is unclear. In the first century, Roman author Pliny made a cryptic reference to adding seashells to the glass melt, but again, without further explanation. [3] Analysis of ancient glass often shows a significant lime content; seemingly more than could be reasonably accounted for by happy accident or contamination. The ingredient is never mentioned in most surviving early recipes. Of course, it may be that  lime is present in many ancient glass artifacts precisely because those artifacts are the ones that have survived without dissolving.

Some have speculated that calcium could have been introduced inadvertently as seashell fragments when sand was crushed into powder for glassmaking. This hypothesis is certainly possible, but it seems suspect considering just how much seashell would be required and how fussy the glassmakers were in obtaining pure white sand from particular locations. However, a distinction must be made between knowing that sand from a particular location makes good glass, and knowing what is in that sand. 

Perhaps the most famous such site for good glassmaking sand is the "Belus" [Na'aman] River outlet in what is now northern Israel. This is where the story of the discovery of glass takes place, as told by Pliny and other early writers. Sailors were driven here by a storm, they used natron (glassmaking salt) [4] from their cargo to hold their cooking pots up over a beach fire, and when the natron mixed with the sand in the fire, glass was formed. Or so the story tells. The nearby Phoenician cities of Tyre and Sidon are known to have hosted a thriving glass industry. The sand in this area is composed of exceptionally pure quartz, with a healthy amount of calcium from shells ground down from wave action. Together these make an ideal mix for stable glass. 

There is some evidence that experimenters such as Basil Valentine were aware that glass without lime would dissolve as early as 1520. [5] For what it is worth, I can contribute some anecdotal evidence from the twentieth century. There is a well-known product called water-glass that is essentially composed of dissolved glass without the lime. [6] My glass artist friend Emilio tells me that growing up on Murano in Venice, his mother regularly preserved fresh eggs by dipping them in water-glass, which when dry, formed a hard seal over the existing shell. Presumably, she learned the technique from her own mother. I do not know of any early references, but the use of water-glass clearly indicates a knowledge of the role lime played.

There are other explanations possible for the addition of lime to glass. Lime was a commodity that was made since ancient times, in furnaces very similar to the ones producing glass. In fact, Neri specifies the use of a “limekiln” for the production of his enamels. The archaeological remains of Tyre and Sidon show prolific use of lime based plaster and mortar in their construction practices and there are indications of lime making facilities. It seems only good business sense that the same furnaces making glass may have also been making lime. Cross contamination, and even experimentation would be a natural outcome. 

[1] Neri 1612, ch 7.
[2] As an aside, magnesia (MgO) can also serve as a stabilizer in glass.
[3] Pliny, Natural History v.36, ch. 66.192.
[4] Natron is a mix of sodium carbonates. 
[5] Basil Valentine, et al. see footnote 6 of the Wikipedia article on sodium silicate for a discussion.
[6] Sodium Silicate.
* This post first appeared here in a slightly different form on 10 October 2014.

Wednesday, December 7, 2016

Roasting the Frit

Diderot & d'Alembert, L'Encyclopédie (1772)
Raking Out Roasted Frit.
Making glass from raw materials involves several steps. In his 1612 book on glass- making, L'Arte Vetraria, Antonio Neri breaks the process down into parts so that, "given a bit of experience and practice, as long as you do not purposely foul-up, it will be impossible to fail." Pure white sand, or preferably quartz river stones which Neri calls "tarso" is broken up and pulverized into a fine powder. The initial work can be done by heating the stones in a furnace, then dropping them into a vat of clean cold water, where they will fracture due to the thermal shock. The process was often repeated multiple times. From there, the pieces are pulverized in a stone mortar and pestle. Stone, because metal tools would contaminate the quartz, and in the end tint the glass. Finally, a powder is obtained by grinding with a stone tool on a flat granite "porphyry stone." This powdered quartz is the main ingredient of glass.

The second critical ingredient is the flux, what Neri calls "glass salt" or "soda." This can be obtained from mineral sources, but European glassmakers in the seventeenth century extracted all their salt from certain plants. The powdered quartz was mixed with the salt and a third ingredient, which is critical, lime. Lime is simply calcium oxide used by builders to make cement. It is nothing more than pulverized seashells roasted to a high temperature. Neri advises using two pounds of lime for every hundred pounds of salt. He specifies that it should be added to all his frit recipes, but it is not clear that he understood its critical importance; without lime, the glass would be subject to attack by mere water, eventually decomposing. This mixture of soda, lime and silica when heated in a kiln would chemically react forming "frit." The combined materials were raked around in a kiln for a long period (many hours) and finally formed nut sized pieces. It was cooled and heaped into piles in dry cellars where it was aged for a time. This is where some chemical "magic" in glassmaking takes place. The glass salt or soda dramatically lowers the melting temperature of the quartz, all the way down to a point that was easily achieved in a wood fired furnace. When a batch of glass was made, the aged frit was then melted in furnace crucibles and skimmed to remove excess salt, which floated on the surface; it could foul the glass, and smelled terrible. The melted glass, now ready to work, was sometimes colored and finally made into objects by gaffers. 

Neri obtained his glass salt from products shipped by traders from the Levant (eastern Mediterranean). It was supplied as the dried, partially charred remains of special plants that grow in arid seaside conditions; 'Kali' and 'Soda'. Shipping them this way cut down on weight and volume, and prevented rotting. These plants contain large amounts of sodium carbonates. This is a white powder, chemically identical to what we know as "washing soda." He advises, 
In buying either of these make sure it is richly salted. This may be determined by touching it with the tongue in order to taste its saltiness; but the surest way of all is to do a test in a crucible and to see if it contains much sand or stones, a thing common in this art and very well known by glass conciatori.
He crushes any large pieces of the product in a stone mortar, and sifts the result through a fine screen, ensuring that most of what remains is salt.  
As the common proverb of the art of glassmaking says: a fine sieve and dry wood bring honor to the furnace. Then with any of these sodas, 100 pounds of soda ordinarily requires 85 to 90 pounds of tarso.
Neri sets up large cauldrons of clean water over brickwork stoves, adds the plant product and boils the water. He strains the insoluble parts out and reduces the liquid by evaporation until crystals of the salt start to form on the surface. He skims these off and continues the process. Finally he carefully dries the product. Our glassmaker describes several variations of this process, including one in which he takes extreme measures to ensure the purity of the salt and clarity of the finished glass. In all, this is a task that could easily take several weeks to perform for the amount of frit to fill a single pot for the gaffer to work.

Not content with the established materials, our glassmaker experimented extensively with other plants: 
Use the husks and stalks of fava beans after the farmhands have thrashed and shelled them. With the rules and diligence prescribed for the Levantine polverino salt, extract the salt from this ash, which will be marvelous, and from which a frit can be made using well-sifted white tarso, as is described throughout this work. A very noble frit will result, which in the crucible will make a crystal of all beauty. The same may be made from the ashes of cabbages, or a thorn bush that bears small fruit, called the blackberry, even from millet, rush, marsh reeds, and from many other plants that will relinquish their salt. *
*These other plants produce potassium carbonate salts with similar properties to sodium carbonate.
** This post first appeared here 9 December 2013.

Wednesday, August 31, 2016

Lime

Vintage 1920's Water Glass Label.
The temperature of 1500 degrees (825 C) was comfortably within reach of seventeenth century glassmakers like Antonio Neri. It was also achievable in much earlier times and was used in one of the earliest chemical reactions of  human industry; the production of "lime" by heating seashells or limestone to the above mentioned temperature. This is the point at which these materials give up the carbon dioxide gas bound into their chemical structure, leaving behind calcium oxide, otherwise known as lime.

What makes lime so useful is a property early Roman engineers knew well; that when mixed with water, lime undergoes a chemical reaction that releases heat and quickly solidifies into a rock-hard mass that is impervious to the elements. The Romans used it as a construction material; they mixed it with ash, clay, sand and stones to form mortar, cement and concrete. It has played a critical role ever since in the construction of buildings, roads and monuments.

Today it is perhaps not an obvious choice in imagining the supplies of a seventeenth century alchemist’s cabinet; lime does not require exotic methods to produce, it was made in industrial quantities and readily available as a construction material. Nevertheless, lime played an important part in many diverse chemical preparations of the day. Antonio Neri mentions it numerous times in his writing. He used it in his lute recipe; a hard, cement like coating which protected alchemical glassware in direct flame and sealed joints. He also used it to extract the color from flowers in the production of paints. Most notably, he used lime as an ingredient in the formulation of glass itself. 

Lime turns out to be a rather critical ingredient in glassmaking and the central player in a mystery about the history of glass that to this day has not been satisfactorily explained. Neri obtained the white powder from suppliers as "lime cake." Early in his book, L'Arte Vetraria, he states it should be used in all his glass recipes. 
Take lime salt, which is used for building. Purify this salt and mix it with ordinary Levantine polverino salt in the proportion of 2 pounds per 100, which is 2 pounds of lime salt, to every 100 pounds of polverino salt, purified and well made, as previously described. With this salt mixture, you can make yourself ordinary frit, and put it in the crucible to clarify. I will refer to this frit from now on in the recipes for cristallino, cristallo, and common glass. This way you will have cristallo quite subtle and beautiful.[1]
The above excerpt is the full extent of Neri's discussion on lime in glassmaking. An interesting point here is that he does not say why lime is so necessary, but it is. [2] He must have known that adding too much lime will cause glass to become cloudy, the exact opposite effect that he was after. What is not so clear is if Neri (or anyone else in that period) knew that too little lime allows glass to dissolve slowly when exposed to water. 

One of the great enduring mysteries in the history of glassmaking is the question of exactly when it was clearly understood that lime was so important. The subject became a matter of deliberate chemical investigation in the eighteenth century, but the use of lime extends much earlier. Some of the earliest glass fragments known contain healthy amounts of lime. Neri's ambiguous endorsement is the first mention in print, but even among much earlier manuscripts, its role is unclear. In the first century, Roman author Pliny made a cryptic reference to adding seashells to the glass melt, but again, without further explanation. [3] Analysis of ancient glass often shows a significant lime content; seemingly more than could be reasonably accounted for by happy accident or contamination. The ingredient is never mentioned in most surviving early recipes. Of course, it may be that  lime is present in many ancient glass artifacts precisely because those artifacts are the ones that have survived without dissolving.

Some have speculated that calcium could have been introduced inadvertently as seashell fragments when sand was crushed into powder for glassmaking. This hypothesis is certainly possible, but it seems suspect considering just how much seashell would be required and how fussy the glassmakers were in obtaining pure white sand from particular locations. However, a distinction must be made between knowing that sand from a particular location makes good glass, and knowing what is in that sand. 

Perhaps the most famous such site for good glassmaking sand is the "Belus" [Na'aman] River outlet in what is now northern Israel. This is where the story of the discovery of glass takes place, as told by Pliny and other early writers. Sailors were driven here by a storm, they used natron (glassmaking salt) [4] from their cargo to hold their cooking pots up over a beach fire, and when the natron mixed with the sand in the fire, glass was formed. Or so the story tells. The nearby Phoenician cities of Tyre and Sidon are known to have hosted a thriving glass industry. The sand in this area is composed of exceptionally pure quartz, with a healthy amount of calcium from shells ground down from wave action. Together these make an ideal mix for stable glass. 

There is some evidence that experimenters such as Basil Valentine were aware that glass without lime would dissolve as early as 1520. [5] For what it is worth, I can contribute some anecdotal evidence from the twentieth century. There is a well-known product called water-glass that is essentially composed of dissolved glass without the lime. [6] My glass artist friend Emilio tells me that growing up on Murano in Venice, his mother regularly preserved fresh eggs by dipping them in water-glass, which when dry, formed a hard seal over the existing shell. Presumably, she learned the technique from her own mother. I do not know of any early references, but the use of water-glass clearly indicates a knowledge of the role lime played.

There are other explanations possible for the addition of lime to glass. Lime was a commodity that was made since ancient times, in furnaces very similar to the ones producing glass. In fact, Neri specifies the use of a “limekiln” for the production of his enamels. The archaeological remains of Tyre and Sidon show prolific use of lime based plaster and mortar in their construction practices and there are indications of lime making facilities. It seems only good business sense that the same furnaces making glass may have also been making lime. Cross contamination, and even experimentation would be a natural outcome. 

[1] Neri 1612, ch 7.
[2] As an aside, magnesia (MgO) can also serve as a stabilizer in glass.
[3] Pliny, Natural History v.36, ch. 66.192.
[4] Natron is a mix of sodium carbonates. 
[5] Basil Valentine, et al. see footnote 6 of the Wikipedia article on sodium silicate for a discussion.
[6] Sodium Silicate.
* This post first appeared here in a slightly different form on 10 October 2014.

Wednesday, December 16, 2015

Roasting the Frit

Diderot & d'Alembert, L'Encyclopédie (1772)Raking Out Roasted Frit
Making glass from raw materials involves several steps. In his 1612 book on glassmaking, L'Arte Vetraria, Antonio Neri breaks the process down into parts so that, "given a bit of experience and practice, as long as you do not purposely foul-up, it will be impossible to fail." Pure white sand, or preferably quartz river stones which Neri calls "tarso" is broken up and pulverized into a fine powder. The initial work can be done by heating the stones in a furnace, then dropping them into a vat of clean cold water, where they will fracture due to the thermal shock. The process was often repeated multiple times. From there, the pieces are pulverized in a stone mortar and pestle. Stone, because metal tools would contaminate the quartz, and in the end tint the glass. Finally, a powder is obtained by grinding with a stone tool on a flat granite "porphyry stone." This powdered quartz is the main ingredient of glass.

The second critical ingredient is the flux, what Neri calls "glass salt" or "soda." This can be obtained from mineral sources, but European glassmakers in the seventeenth century extracted all their salt from certain plants. The powdered quartz was mixed with the salt and a third ingredient, which is critical, lime. Lime is simply calcium oxide used by builders to make cement. It is nothing more than pulverized seashells roasted to a high temperature. Neri advises using two pounds of lime for every hundred pounds of salt. He specifies that it should be added to all his frit recipes, but it is not clear that he understood its critical importance; without lime, the glass would be subject to attack by mere water, eventually decomposing. This mixture of soda, lime and silica when heated in a kiln would chemically react forming "frit." The combined materials were raked around in a kiln for a long period (many hours) and finally formed nut sized pieces. It was cooled and heaped into piles in dry cellars where it was aged for a time. This is where some chemical "magic" in glassmaking takes place. The glass salt or soda dramatically lowers the melting temperature of the quartz, all the way down to a point that was easily achieved in a wood fired furnace. When a batch of glass was made, the aged frit was then melted in furnace crucibles and skimmed to remove excess salt, which floated on the surface; it could foul the glass, and smelled terrible. The melted glass, now ready to work, was sometimes colored and finally made into objects by gaffers. 

Neri obtained his glass salt from products shipped by traders from the Levant (eastern Mediterranean). It was supplied as the dried, partially charred remains of special plants that grow in arid seaside conditions; 'Kali' and 'Soda'. Shipping them this way cut down on weight and volume, and prevented rotting. These plants contain large amounts of sodium carbonates. This is a white powder, chemically identical to what we know as "washing soda." He advises, 
In buying either of these make sure it is richly salted. This may be determined by touching it with the tongue in order to taste its saltiness; but the surest way of all is to do a test in a crucible and to see if it contains much sand or stones, a thing common in this art and very well known by glass conciatori.
He crushes any large pieces of the product in a stone mortar, and sifts the result through a fine screen, ensuring that most of what remains is salt.  
As the common proverb of the art of glassmaking says: a fine sieve and dry wood bring honor to the furnace. Then with any of these sodas, 100 pounds of soda ordinarily requires 85 to 90 pounds of tarso.
Neri sets up large cauldrons of clean water over brickwork stoves, adds the plant product and boils the water. He strains the insoluble parts out and reduces the liquid by evaporation until crystals of the salt start to form on the surface. He skims these off and continues the process. Finally he carefully dries the product. Our glassmaker describes several variations of this process, including one in which he takes extreme measures to ensure the purity of the salt and clarity of the finished glass. In all, this is a task that could easily take several weeks to perform for the amount of frit to fill a single pot for the gaffer to work.

Not content with the established materials, our glassmaker experimented extensively with other plants: 
[U]se the husks and stalks of fava beans after the farmhands have thrashed and shelled them. With the rules and diligence prescribed for the Levantine polverino salt, extract the salt from this ash, which will be marvelous, and from which a frit can be made using well-sifted white tarso, as is described throughout this work. A very noble frit will result, which in the crucible will make a crystal of all beauty. The same may be made from the ashes of cabbages, or a thorn bush that bears small fruit, called the blackberry, even from millet, rush, marsh reeds, and from many other plants that will relinquish their salt. *
*These other plants produce potassium carbonate salts with similar properties to sodium carbonate.
** This post first appeared here 9 December 2013.

Monday, August 31, 2015

Glass Salt

Diderot & d'Alembert, L'Encyclopédie (1772)Raking Out Roasted Frit
Making glass from raw materials involves several steps. In his 1612 book on glassmaking, L'Arte Vetraria, Antonio Neri breaks the process down into parts so that, "given a bit of experience and practice, as long as you do not purposely foul-up, it will be impossible to fail." Pure white sand, or preferably quartz river stones which Neri calls "tarso" is broken up and pulverized into a fine powder. The initial work can be done by heating the stones in a furnace, then dropping them into a vat of clean cold water, where they will fracture due to the thermal shock. The process was often repeated multiple times. From there, the pieces are pulverized in a stone mortar and pestle. Stone, because metal tools would contaminate the quartz, and in the end tint the glass. Finally, a powder is obtained by grinding with a stone tool on a flat granite "porphyry stone." This powdered quartz is the main ingredient of glass.

The second critical ingredient is the flux, what Neri calls "glass salt" or "soda." This can be obtained from mineral sources, but European glassmakers in the seventeenth century extracted all their salt from certain plants. The powdered quartz was mixed with the salt and a third ingredient, which is critical, lime. Lime is simply calcium oxide used by builders to make cement. It is nothing more than pulverized seashells roasted to a high temperature. Neri advises using two pounds of lime for every hundred pounds of salt. He specifies that it should be added to all his frit recipes, but it is not clear that he understood its critical importance; without lime, the glass would be subject to attack by mere water, eventually decomposing. This mixture of soda, lime and silica when heated in a kiln would chemically react forming "frit." The combined materials were raked around in a kiln for a long period (many hours) and finally formed nut sized pieces. It was cooled and heaped into piles in dry cellars where it was aged for a time. This is where some real "magic" in glassmaking takes place. The glass salt or soda dramatically lowers the melting temperature of the quartz, all the way down to a point that was easily achieved in a wood fired furnace. When a batch of glass was made, the aged frit was then melted in furnace crucibles and skimmed to remove excess salt, which floated on the surface; it could foul the glass, and smelled terrible. The melted glass, now ready to work, was sometimes colored and finally made into objects by gaffers. 

Neri obtained his glass salt from products shipped by traders from the Levant (eastern Mediterranean). It was supplied as the dried, partially charred remains of special plants that grow in arid seaside conditions. Shipping them this way cut down on weight and volume, and prevented rotting. These Soda and Kali plants contain large amounts of sodium carbonates. This is a white powder, chemically identical to what we know as "washing soda." He advises, 
In buying either of these make sure it is richly salted. This may be determined by touching it with the tongue in order to taste its saltiness; but the surest way of all is to do a test in a crucible and to see if it contains much sand or stones, a thing common in this art and very well known by glass conciatori.
He crushes any large pieces of the product in a stone mortar, and sifts the result through a fine screen, ensuring that most of what remains is salt.  
As the common proverb of the art of glassmaking says: a fine sieve and dry wood bring honor to the furnace. Then with any of these sodas, 100 pounds of soda ordinarily requires 85 to 90 pounds of tarso.
Neri sets up large cauldrons of clean water over brickwork stoves, adds the plant product and boils the water. He strains the insoluble parts out and reduces the liquid by evaporation until crystals of the salt start to form on the surface. He skims these off and continues the process. Finally he carefully dries the product. Our glassmaker describes several variations of this process, including one in which he takes extreme measures to ensure the purity of the salt and clarity of the finished glass. In all, this is a task that could easily take several weeks to perform for the amount of frit to fill a single pot for the gaffer to work.

Not content with the established materials, our glassmaker experimented extensively with other plants: 
[U]se the husks and stalks of fava beans after the farmhands have thrashed and shelled them. With the rules and diligence prescribed for the Levantine polverino salt, extract the salt from this ash, which will be marvelous, and from which a frit can be made using well-sifted white tarso, as is described throughout this work. A very noble frit will result, which in the crucible will make a crystal of all beauty. The same may be made from the ashes of cabbages, or a thorn bush that bears small fruit, called the blackberry, even from millet, rush, marsh reeds, and from many other plants that will relinquish their salt. *
*These other plants produce potassium carbonate salts with similar properties to sodium carbonate.
** This post first appeared here 9 December 2013.

Wednesday, August 26, 2015

Lime

Vintage 1920's Water Glass Label.
The temperature of 1500 degrees (825 C) was comfortably within reach of seventeenth century glassmakers like Antonio Neri. It was also achievable in much earlier times and was used in one of the earliest chemical reactions of  human industry; the production of "lime" by heating seashells or limestone to the above mentioned temperature. This is the point at which these materials give up the carbon dioxide gas bound into their chemical structure, leaving behind calcium oxide, otherwise known as lime.

What makes lime so useful is a property early Roman engineers knew well; that when mixed with water, lime undergoes a chemical reaction that releases heat and quickly solidifies into a rock-hard mass that is impervious to the elements. The Romans used it as a construction material; they mixed it with ash, clay, sand and stones to form mortar, cement and concrete. It has played a critical role ever since in the construction of buildings, roads and monuments.

Today it is perhaps not an obvious choice in imagining the supplies of a seventeenth century alchemist’s cabinet; lime does not require exotic methods to produce, it was made in industrial quantities and readily available as a construction material. Nevertheless, lime played an important part in many diverse chemical preparations of the day. Antonio Neri mentions it numerous times in his writing. He used it in his lute recipe; a hard, cement like coating which protected alchemical glassware in direct flame and sealed joints. He also used it to extract the color from flowers in the production of paints. Most notably, he used lime as an ingredient in the formulation of glass itself. 

Lime turns out to be a rather critical ingredient in glassmaking and the central player in a mystery about the history of glass that to this day has not been satisfactorily explained. Neri obtained the white powder from suppliers as "lime cake." Early in his book, L'Arte Vetraria, he states it should be used in all his glass recipes. 
Take lime salt, which is used for building. Purify this salt and mix it with ordinary Levantine polverino salt in the proportion of 2 pounds per 100, which is 2 pounds of lime salt, to every 100 pounds of polverino salt, purified and well made, as previously described. With this salt mixture, you can make yourself ordinary frit, and put it in the crucible to clarify. I will refer to this frit from now on in the recipes for cristallino, cristallo, and common glass. This way you will have cristallo quite subtle and beautiful.[1]
The above excerpt is the full extent of Neri's discussion on lime in glassmaking. An interesting point here is that he does not say why lime is so necessary. [2] He must have known that adding too much lime will cause glass to become cloudy, the exact opposite effect that he is after. What is not so clear is if Neri (or anyone else) understood that too little lime allows glass to dissolve slowly when exposed to water. 

One of the great enduring mysteries in the history of glassmaking is the question of exactly when it was understood that lime was so important. The subject became a matter of deliberate chemical investigation in the eighteenth century, but the use of lime extends much earlier. Some of the earliest glass fragments known contain healthy amounts of lime. Neri's ambiguous endorsement is the first mention in print, but even among much earlier manuscripts, its role is unclear. In the first century, Roman author Pliny made a cryptic reference to adding seashells to the glass melt, but again, without further explanation. [3] Analysis of ancient glass often shows a significant lime content; seemingly more than could be reasonably accounted for by happy accident or contamination. The ingredient is never mentioned in most surviving early recipes. Of course, it may be that  lime is present in many ancient glass artifacts precisely because those artifacts are the ones that have survived without dissolving.

Some have speculated that calcium could have been introduced inadvertently as seashell fragments when sand was crushed into powder for glassmaking. This hypothesis is certainly possible, but it seems suspect considering just how much seashell would be required and how fussy the glassmakers were in obtaining pure white sand from particular locations. However, a distinction must be made between knowing that sand from a particular location makes good glass, and knowing what is in that sand. 

Perhaps the most famous such site for good glassmaking sand is the "Belus" [Na'aman] River outlet in what is now northern Israel. This is where the story of the discovery of glass takes place, as told by Pliny and other early writers. Sailors were driven here by a storm, they used natron (glassmaking salt) [4] from their cargo to hold their cooking pots up over a beach fire, and when the natron mixed with the sand in the fire, glass was formed. Or so the story tells. The nearby Phoenician cities of Tyre and Sidon are known to have hosted a thriving glass industry. The sand in this area is composed of exceptionally pure quartz, with a healthy amount of calcium from shells ground down from wave action. Together these make an ideal mix for stable glass. 

There is some evidence that experimenters such as Basil Valentine were aware that glass without lime would dissolve as early as 1520. [5] For what it is worth, I can contribute some anecdotal evidence from the twentieth century. There is a well-known product called water-glass that is essentially composed of dissolved glass without the lime. [6] My glass artist friend Emilio tells me that growing up on Murano in Venice, his mother regularly preserved fresh eggs by dipping them in water-glass, which when dry, formed a hard seal over the existing shell. Presumably, she learned the technique from her own mother. I do not know of any early references, but the use of water-glass clearly indicates a knowledge of the role lime played.

There are other explanations possible for the addition of lime to glass. Lime was a commodity that was made since ancient times, in furnaces very similar to the ones producing glass. In fact, Neri specifies the use of a “limekiln” for the production of his enamels. The archaeological remains of Tyre and Sidon show prolific use of lime based plaster and mortar in their construction practices and there are indications of lime making facilities. It seems only good business sense that the same furnaces making glass may have also been making lime. Cross contamination, and even experimentation would be a natural outcome. 

[1] Neri 1612, ch 7.
[2] As an aside, magnesia (MgO) can also serve as a stabilizer in glass.
[3] Pliny, Natural History v.36, ch. 66.192.
[4] Natron is a mix of sodium carbonates. 
[5] Basil Valentine, et al. see footnote 6 of the Wikipedia article on sodium silicate for a discussion.
[6] Sodium Silicate.
* This post first appeared here in a slightly different form on 10 October 2014.

Friday, March 20, 2015

Cristallo

Dragon-stem goblet, Venice, Italy, 
(or in the Venetian style), 17th cent.
Corning Museum of Glass 51.3.118.
Venetian cristallo is quite literally the glass that made Murano famous. Ultimately, royal courts and wealthy families throughout Europe coveted glassware of this type. It had the clarity of its namesake mineral, rock crystal, and its working properties were such that one could make extremely thin, yet complex pieces. At a time when glass made from dirty sand and fireplace ash was churned out cheaply and quickly around Europe, cristallo was the absolute pinnacle of the glassmaker's art.

Murano glassmaker Angelo Barovier gets credit for the development of cristallo around the year 1450. However, it is a mistake to think that suddenly, he exclaimed "eureka" and burst out of his workshop with an entirely new invention. The predecessor of cristallo was what Antonio Neri called cristallino, which already incorporated some of the advantages. Barovier may well be responsible for bringing together the ultimate refinements that elevated cristallino to a new level of perfection, but these techniques individually were all available and utilized by glassmakers at least fifty years earlier. 

Barovier had attended lectures by noted alchemist Paola de Pergola, at the School of Rialto. This indicates that he was thinking along the lines of a chemist in putting together a repeatable regimen for an exceptionally clear, bright, workable product. The real genius in cristallo was in controlling the purity and quality of all the materials through Venice's extensive trade network in the Mediterranean. Even if the recipe leaked out, exclusive trade agreements blocked access to the raw materials. Local ordinances tightly controlled source materials used in the furnaces to ensure consistency, from the quartz river pebbles crushed for frit, to the plants used to make the flux, to the manganese which eliminated any slight tinting. Requirements even stipulated the making of the furnace crucibles from a specific variety of clay from Constantinople.

Barovier's innovation would become a tradition that would be carried on by countless glassmakers and ultimately by our Florentine priest, Antonio Neri, more than a century and a half later. Neri describes the Venetian methods, but then goes on to innovate with variations of his own. Numerous family manuscripts in Venice documented the method to make cristallo; what Neri did was to publish these relatively secret techniques and make them available to anyone who could read his book, and many did. 

For silica, the main ingredient in glass, Neri says the craftsmen on Murano specifically used quartz river pebbles (tarso) from the Ticino River in Pavia. He describes special procedures to pulverize the stones without contamination, into a powder "ground as finely as flour." Next, he makes the flux (glass salt), which allows the quartz to melt at lower temperatures. He says to use the ash of the kali plant from Syria (polverino and rocchetta). This plant ash is very rich in sodium carbonates; he extracts and purifies it in a process called lixiviation. Neri purchased the starting material in a charred state, which reduces it weight and volume for shipping. From 300 pounds of ash, he usually produced 80-90 pounds of salt. The ash was boiled in cauldrons full of water, strained, filtered, evaporated and dried leaving the all important glass salt. Into each cauldron, he mixes ten pounds of tartar—the dried dregs scraped from the inside of red wine barrels—a material high in potassium carbonates. Today, we know the soda component is responsible for the favorable property of long working times for artisans before the hot glass stiffens, the potassium adds sparkle. The final ingredient was two pounds of lime (calcium oxide) per one hundred pounds of salt, which is added to the dry salt because it is not water soluble. This stabilized the glass against future degradation by moisture over time. 

200 pounds of powdered quartz mixed thoroughly with 130 pounds of the salt forms the basis of the frit. He raked the powder around in a hot kiln for about five hours, until "nut sized" pieces began to form. Now this cristallo frit,—which Neri calls bollito—was carefully packed to remain dry and allowed to age for three or four months, when it was ready to melt in the furnace. If the glass should have a slight green tint from iron tools, it was corrected with manganese (oxide), specifically mined in the Piedmont region. The cristallo was boiled for up to six days and repeatedly washed by ladeling the hot glass into cold water and then remelting.

The result was a glass that was a pleasure for artisans to work and make finished pieces over which royalty clamored. Cristallo was uniform in consistency, it could be blown into molds or worked freehand into complex shapes, like the iconic "dragon goblet" form, which became a hallmark of the Venetian masters.

In the Cathedral of Santa Maria and Donato on Murano, behind the altar, there is an unusual display of four very large bones found buried under the ancient church. Local folklore tells that the bones belong to a dragon slayed by Saint Donatus of Arezzo, the patron saint of the island.


* This post first appeared here in a slightly shorter form on 12 February 2014.

Friday, January 9, 2015

Le Fritte

Diderot & d'Alembert, L'Encyclopédie (1772)
Raking Out Roasted Frit
In the opening chapters of Antonio Neri’s 1612 book, L’Arte Vetraria, he details the production of a little appreciated invention, which had a tremendous impact on the technical art of glassmaking. The development of “frit” or as Neri termed it “le fritte” is nothing less than the product that makes glass possible. [1] 

The legend about how glass was first discovered centers around the chance combination of the critical ingredients plus the all-important intense heat necessary to melt them. The only problem is that if you throw the ingredients of glass into a pot and heat them, what you get is a really hot pot of ingredients that have no intention of forming glass. Even two-thousand years ago, we could not resist the allure of a story line in which a sudden discovery changed history. The truth about glass is probably a lot less dramatic and a lot more gradual. Therein lays the widely neglected and underappreciated technical innovation of frit. To form glass, the ingredients were first pulverized to a fine powder, thoroughly mixed, heated and raked together continuously for a long period of time. The result was then allowed to cool and sit in heaps for several weeks or months where the ingredients continued to chemically react. They formed a solid mass that was then cracked apart and often reground into a granular form again; this is “frit” and when this was heated in a crucible it did readily form glass.

Frit is an intermediate product between raw materials and finished glass. It allows transparent glass to form quickly, efficiently and without being saturated with gas bubbles. It also has close ties to the formulation of ancient precursors to glass; to Egyptian faience as well as to pottery glazes and even some fired clay formulations. [2] The implication is that glass as we know it today is the result of a gradual evolution and refinement that started with clay pottery, but there simply is not enough evidence to draw such a conclusion. Frit falls into a grey area of technical history where we do not have enough information to form a narrative and therefore there is no ‘story’ to latch onto. As a result, frit has taken a place on the sidelines. All we have is tantalizing clues from the chemical analysis of archaeological finds. Nevertheless, by the time Antonio Neri came along in the early seventeenth century, fritting was a standard intermediate step in making glass, a necessary step, and Neri left us a detailed, coherent account.  
It is important that the tarso is ground as finely as flour, so that it will all pass through a fine sieve. Now take 200 pounds of the best finely sifted tarso [crushed quartz], as before, and about 130 pounds of polverino salt [soda] ground and sifted, as before, and stir everything thoroughly and blend it together in its entirety. Once fully mixed, put it in a kiln that has been well heated in advance, because if it were put into a cold kiln the frit would never form. I begin with a moderate fire for an hour, always stirring with the rake and mixing the frit until it is well incorporated and calcined [roasted], then I stoke the fire. Continuously mix the frit well with the rake, which is very important. Keep on doing this without fail for 5 hours, maintaining the strong fire. […] 
Keep this crystal frit, as said before, in a dry place where it is not exposed to moisture, because in regions and places that are humid it will suffer greatly. Soon the salt would soak up water and would dissolve away; all that would remain is the tarso alone which would not vitrify. Furthermore, this frit should not be washed the way others are. When it is allowed to rest for 3 or 4 months it is in much better shape to put in crucibles [in the furnace], and will clarify sooner. This is the way to make crystal frit with its dosages and circumstances as I have made many times. [3]
Neri is recounting long tradition here, possibly extending back to the Roman Empire. Frit is a necessary and deliberate step to the reliable production of glass. It speaks to a significant specialization within the glass industries of antiquity. When we look for similar activity we find occupations like the making of cement by roasting seashells or limestone for long periods. This is perhaps a clue to the introduction of lime, the third ingredient necessary for glass. 

[1] In modern parlance “frit” is most often used to describe finished glass that has been crushed for various artistic purposes.
[2] Wikipedia has a good synopsis, http://en.wikipedia.org/wiki/Frit
[3] Neri 1612, chap. 2.